Posts Tagged ‘Asterisk’

After a yum update and later on a reboot I broke my Trixbox 2.8 / Nagios server as it wasn’t dialing out anymore using the FXO card attached to the server. The server dials out thanks to Asterisk performing a text2speech function which eventually results in a call to me through one of my company’s POTS. After some research and log searching I got the following errors identified:

Loading DAHDI hardware modules:
FATAL: Module dahdi not found.
wct4xxp:  FATAL: Module wct4xxp not found.       [FAILED]
wcte12xp:  FATAL: Module wcte12xp not found.     [FAILED]
wct1xxp:  FATAL: Module wct1xxp not found.       [FAILED]
wcte11xp:  FATAL: Module wcte11xp not found.     [FAILED]
wctdm24xxp:  FATAL: Module wctdm24xxp not found. [FAILED]
wcfxo:  FATAL: Module wcfxo not found.           [FAILED]
wctdm:  FATAL: Module wctdm not found.           [FAILED]
wcb4xxp:  FATAL: Module wcb4xxp not found.       [FAILED]
wctc4xxp:  FATAL: Module wctc4xxp not found.     [FAILED]
xpp_usb:  FATAL: Module xpp_usb not found.       [FAILED]
Error: missing /dev/dahdi!

The error could be duplicated by trying to start the dahdi service (# service dahdi start) or by simply restarting the server and looking at server load up.

Researching the forums showed that Trixbox 2.8 now uses dahdi modules instead of zap modules but I had the dahdi modules and packages installed, which led me to see what kernel I was actually running, it seemed I was actually running a XEN kernel, 2.6.18-164.11.1.el5xen to be exact, a-ha!

I am unsure why I had installed XEN kernels but it must have been a mistake and 2.6.18-164.11.1.el5xen was set up as my default kernel boot option. I uninstalled kernels, rebooted, ran setup-pstn and it’s all back to normal!

[root@hostname][~]# cat /etc/grub.conf
# grub.conf generated by anaconda
#
# Note that you do not have to rerun grub after making changes to this file
# NOTICE:  You have a /boot partition.  This means that
#          all kernel and initrd paths are relative to /boot/, eg.
#          root (hd0,0)
#          kernel /vmlinuz-version ro root=/dev/sda2
#          initrd /initrd-version.img
#boot=/dev/sda
default=0
timeout=5
splashimage=(hd0,0)/grub/splash.xpm.gz
#hiddenmenu
title CentOS (2.6.18-164.11.1.el5)
        root (hd0,0)
        kernel /vmlinuz-2.6.18-164.11.1.el5 ro root=LABEL=/
        initrd /initrd-2.6.18-164.11.1.el5.img
title trixbox-base (2.6.18-128.1.10.el5)
        root (hd0,0)
        kernel /vmlinuz-2.6.18-128.1.10.el5 ro root=LABEL=/
        initrd /initrd-2.6.18-128.1.10.el5.img
[root@hostname][~]# dahdi_cfg -vv
DAHDI Tools Version - 2.2.1
DAHDI Version: 2.2.1
Echo Canceller(s): MG2
Configuration
======================
Channel map:
Channel 01: FXS Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 01)
1 channels to configure.
Setting echocan for channel 1 to mg2
[root@hostname][~]# /etc/init.d/dahdi restart
Unloading DAHDI hardware modules: ERROR: Module dahdi_echocan_mg2 is in use
ERROR: Module wcfxo is in use
ERROR: Module dahdi is in use by dahdi_echocan_mg2,wcfxo
error
Loading DAHDI hardware modules:
  wct4xxp:                                                 [  OK  ]
  wcte12xp:                                                [  OK  ]
  wct1xxp:                                                 [  OK  ]
  wcte11xp:                                                [  OK  ]
  wctdm24xxp:                                              [  OK  ]
  wcfxo:                                                   [  OK  ]
  wctdm:                                                   [  OK  ]
  wcb4xxp:                                                 [  OK  ]
  wctc4xxp:                                                [  OK  ]
  xpp_usb:                                                 [  OK  ]
Running dahdi_cfg:                                         [  OK  ]